Plumbing Basics: The First Step for Bathtub Installation
Plumbing Basics: The First Step for Bathtub Installation
Blog Article
This article listed below on the subject of A Step-by-Step Guide to Installing a Bathtub is quite insightful. You should check it out.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Setting up a tub isn't specifically brain surgery, but it does require strong plumbing, carpentry, and often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately hard project. If the old bathtub is easily accessible, the project can move speedily; if you have to open a wall surface to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either situation, the task is within a house handyman's abilities, although you will require a helper to leave the old bathtub and set in the brand-new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of working with a service provider to take over a halfway-completed project, it is better to take into consideration utilizing one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This write-up will certainly assist you set up a brand-new bathtub in your bathroom if you have already gotten a new bathtub and also do not require to change the arrangement of your previous water system pipelines.
Your tools as well as product checklist should comprise the following:
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your setup, then the first thing you must do is disconnect the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite troublesome as a result of the restricted access that is often the case.
Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will certainly originate from the pipelines. When the supply pipelines have been eliminated, utilize the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. Once the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipe links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next off, place the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the tap in place with the manufacturer offered backnut. Once the tap is safely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet adapters. The previous type must be linked to the faucet ends initially, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Making use of the two wooden boards under its feet, put the bathtub in the required placement. The wooden boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 tiny points.
The following objective is to guarantee that the tub is leveled all round. This can be attained by checking the spirit level and also adjusting the feet on the bathtub up until the level reviews degree.
To mount taps, fit the bottom of the furthest versatile tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water supply and inspect all joints and new pipework for leaks and also tighten them if required. Load the bath tub and also inspect the overflow outlet as well as the normal outlet for leakages.
Ultimately, fix the bathroom paneling as defined in the producer's user's manual. Tiling and also securing around the bath tub should wait up until the bathtub has been utilized at the very least when as this will certainly resolve it into its last setting.
Getting ready for the Installment
First of all, the supporting frame supplied with the bath needs to be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.
Tiling Around the Bathtub
In the location where the bathroom meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is important as the fitting can move sufficient to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, leading to complications with moisture as well as possible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the tub remains in usage. The sealant can break rather early if you do not consider this activity before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
We had been brought to that article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on another web address. Please take the opportunity to share this blog entry if you enjoyed reading it. I truly appreciate reading our article about How to Install a Bathtub.
Leaks? Contact us! Report this page